<rp id="jcirx"></rp>
    <font id="jcirx"><tr id="jcirx"></tr></font>

    <rt id="jcirx"><meter id="jcirx"></meter></rt>
    <rp id="jcirx"><meter id="jcirx"><button id="jcirx"></button></meter></rp>

      泰安揚帆數控科技有限公司為您提供山東焊接專機等相關信息發布和資訊展示,敬請關注!
      咨詢服務熱線:
      0538-5358300

      新聞資訊

      推薦產品

      公司新聞

      山東焊接專機共5步操作流程掌握嗎

      來源:http://www.railway-signal.com/  發布時間:2021-12-02 瀏覽次數:

      焊接機安全操作規程(焊機維修規程)啟動后,應先空運轉,檢查各傳動部件及軸承運轉正常后,方可操作。
      Welding Machine Safety Operating Procedures (welding machine maintenance procedures) start, should first air operation, inspection of the transmission parts and normal operation of bearings, before the operation.
      山東焊接專機共5步操作流程掌握嗎?
      Shandong welding machine total 5 Steps Operation Process Control?
      1.起動前,必須檢查切刀是否有裂紋,刀架螺栓緊固,防護罩牢固.再用手轉動輪齒,檢查齒輪嚙合間隙,調整刀片間隙.
      1. Before starting, must check whether the cutter has cracks, knife frame bolt fastening, shield firm. Turn the gear tooth by hand, check the meshing clearance of the gear and adjust the blade clearance.
      2、當機器沒有達到正常轉速時,山東焊接專機不能切割,必須使用切割刀的中下位置,握持鋼筋對著刀口快速送進,操作者應站在固定刀片的一側用力壓住鋼筋,防止鋼筋末端彈出傷人.嚴禁用兩手在刀片上夾住鋼筋。
       2, when the machine does not reach the normal speed, can not cut, must use the cutting knife in the lower position, holding the steel bar to the edge of the knife, the operator should stand on the side of the fixed blade to press the steel bar, prevent the end of the steel bar from popping out and hurting people. It is strictly forbidden to clamp the rebar on the blade with both hands.
      3.起動后,應先空運轉,檢查各傳動部件和軸承運轉正常后方可使用。
      3. After starting, should first air running, check the transmission parts and bearings running properly before use. 
      4.不得剪切直徑和強度超過機械銘牌規定的鋼筋和燒紅的鋼筋.當一次切斷多根鋼筋時,其總截斷面積應在規定范圍內。
      4. Shall Not Shear diameter and strength over the mechanical nameplate provisions of the reinforcement and red-hot reinforcement. When cutting several reinforcing bars at one time, the total cut-off area should be within the prescribed range. 
      5.送料的工作臺面應和刀片下部保持水平,山東焊接專機工作臺長度可根據加工材料長度確定,加工較長的鋼筋時,應專人協助,聽從操作人員指揮,不得任意推拉。
      5. Feed table should be level with the lower part of the blade, table length can be determined according to the length of processing materials. When processing longer steel bar, should be specialized assistance, follow the operator’s command, not arbitrary push and pull.

      上一篇:山東數控焊接設備管板焊機的焊接
      下一篇:山東數控焊接設備的3個裝置

      欧美大胆无码视频